|
|
Iscar Offers A Completely New Line Of Slitting Cutters Applying Tang-Grip Technology And The Strength Of Sumo Tec Grades
Iscar right now offers a family of high-performance slitting tools that merge the convenience and security of Tang-Grip clamping with the increased strength of the brand new Sumo Tec insert grades.
The idea, already verified successful in Tang-Grip parting tools, has now been extended to slitting cutters. In the patented Tang-Grip clamping system, inserts are press-fit into their pockets accompanying a specific hand tool, and are clutched tightly in place without the need for clamps, upper jaws or set screws that can weaken the insert and block chip flow. The pocket composition uses cutting forces to keep the insert seated solidly in position, removing any prospect of insert pull-out. The Tang-Grip clamping system also fosters increased accurate slitting cuts plus lengthened pocket and insert life.
Iscar's Sumo Tec insert grades feature a unique post-coating treatment which substantially improves tool life and constancy.
Launched in late 2007, the completely new Sumo Tec treatment flattens the insert's coated surface to eradicate microscopic stress raisers, decrease heat and friction and increase chip flow. The result is improved toughness and resistance to chipping and built-up edge, all leading to enhanced tool lifespan. The golden-colored side on Sumo Tec inserts aides wear detection. Size for size, Tangslit cutters give more teeth than Iscar's SGSF cutters, allowing higher feed rates.
Their higher rigidity leads to straighter, additional accurate cuts and less vibration even in large-diameter cutters. The new Tangslit TGSF cutters come in 100 to 160 mm diameters, 3 and 4 mm widths and can accept the exact same variety of inserts as Tang-Grip parting tools. Some other sizes will be added.
Existing Sumo Tec grades for Tangslit cutters include:
IC808, with a tough submicron substrate below a Sumo Tec TiAlN PVD coating, delivering superb resistance to impact loads and built-up edge. This grade is suggested for slitting heat resistant alloys, austenitic stainless steel, hard alloys and carbon steel.
IC830, offering greater toughness for heavier parting & grooving including interrupted cuts. It is suited for every stainless steel and high temperature alloys.
IC908, a hard, fine-grain substrate with exceptional chipping resistance, mixed with a new Sumo Tec TiAlN PVD coating. It is ideal for nodular or grey cast iron.
IC928 and 928A, PVD TiAlN-coated tough grades fitting for stainless steel, high temperature alloys and other alloy steels. These grades are likewise suggested for interrupted cuts and heavy operations.
Every Tangslit and Tang-Grip inserts are presented in J- or C-type chipformer geometries from Iscar.
New End Mills Coming From Iscar Can Increase Productivity While Shrinking Costs
Manufacturers and die & mold shops can banish chatter problems in numerous milling operations with Iscar's new Chatterfree end mills. The cutters' variable-pitch flute pattern eliminates harmonic vibration, the primary source of chatter. This enables faster cutting and finer finish in rough or finish slotting, shoulder milling and cavity milling.
Iscar Adds Their Most Recent Creations To A Extended Line Of Prosperous Hole Making Solutions
Iscar recently released several different drilling innovations to meet their customers needs. These new products are Sumocham Drill, DR-DH and Deep Drills. Drawing off of their experience Iscar has come up with new and innovative ways to increase productivity for the end user.
Iscar Recently Made Public A Variety Of Original Lines To Increase Their Family Of Milling Cutters
Iscar recently released a new family of High Speed Milling adjustable endmills and facemills that will improve milling of aluminum, non-metallics, cast iron and hardened steel. This should prove especially useful in the automotive and aerospace industries.
The Latest In Carbide Endmill Designs In A Extensive And Effective Family From Iscar
Manufacturers and die & mold shops can eliminate chatter problems in many milling operations with Iscar's new Chatterfree endmills. The cutters' variable-pitch flute pattern eliminates harmonic vibration, the main source of chatter. This enables faster cutting and finer finish in rough or finish slotting, shoulder milling and cavity milling.
A Couple Of The Numerous Improvements In Carbide Inserts From Iscar Over The Years
Iscar is introducing a new unique milling system with tangential, clamped, butterfly-shaped LNKX carbide inserts. The butterfly-shaped insert has significant advantages compared to the current flat, square shapes. The new geometry has more cutting edges, positive rake face, reduced cutting forces resulting in higher performance.
New Tools And Carbide Insert Arrangements From Iscar To Better Maximize The Machining Procedure
Iscar is introducing Penta 34 carbide inserts with a new PB chipformer. The PB chipformer features a single cavity with a positive rake, neutral shoulder angle, and a honed edge. It is actually a C-type chipformer with a different frontal edge.
Industrial Water Heater - Considering All Of Your Requirements - Read Carefully In Order To Learn A Lot More
Looking into a commercial water heater? Then you have a few things that you must consider. Take a look at these areas to avoid making a mistake with the wrong unit.
Brand New Car Manufacturing Jobs To Save The Overall Economy
The global recession the economy is experiencing in the past few years have pushed major companies to close down and stop their operations.
|
More Articles
Blogroll
|
